Description
EMCgear Digital optical fiber link EFL-D is a range of products designed to isolate digital signals between two locations, especially in EMC test laboratories and DUT monitoring or stimulation systems.
Two or four digital channels with a sample rate of 5 MSa/s per channel transfer sampled logic states between the Input and Output units. Input and output logic levels of 2.5 V, 3.3 V and 5 V are selected according to the required variant, supporting integration with different logic interfaces.
FPGA-based communication with real-time CRC-5 validation protects every transmitted data frame. The receiver monitors link validity and controls the digital outputs. Short-circuit protection is provided on the outputs.
Aluminum housings and filtered electrical interfaces support use in EMC test environments. The optical fiber connection separates the Input and Output units without an electrical signal connection, while battery operation provides a typical operating time of 20 hours.
Product datasheet
EFL-D_Datasheet_Manual_v1.0.pdf
Pricing / lead-time
For the current price list and lead-time information, please send your request using the Request Quote button or the contact form on our website. We will get back to you within 24 hours.
Features
| Battery operated digital link with 2.5 V, 3.3 V or 5 V input / output logic levels |
| 2 or 4 digital channels per link |
| Sample rate of 5 MSa/s per channel |
| FPGA-based communication with CRC-5 protection on every data frame |
| Short-circuit protected digital outputs |
| Designed for EMC test labs with optical signal isolation |
| Typical operating time of 20 hours |
| 820 nm SMA-905 optical interface |
Technical parameters – General
| Channels *) | 2 or 4 |
| Signal type | Digital logic |
| Input logic levels *) | 2.5 V / 3.3 V / 5 V |
| Output logic levels *) | 2.5 V / 3.3 V / 5 V |
| Sample rate | 5 MSa/s per channel (2-channel and 4-channel versions) |
| Input impedance | 100 kOhm |
| Input capacitance | 27 pF |
| Input filter cutoff frequency | 10.6 MHz |
| Output impedance | 100 Ohm |
| Output current / overload limit | ±25 mA |
| Output short-circuit protection | Yes |
| Data integrity protection | CRC-5 on every data frame |
| Optical interface | 2 × SMA-905, 820 nm |
| Recommended optical fiber length | 0 to 900 m |
| Battery | 4.2 V / 5000 mAh, 1-cell LiPo |
| Operating time | Typ. 20 hours |
| Operating temperature | 0 to 55 °C |
*) Variant dependent. Please specify the required number of channels and input / output logic levels in your request for quotation.
The input filter cutoff frequency is not the guaranteed maximum digital toggle frequency. Minimum pulse width, propagation delay, jitter and input thresholds are not yet specified in the v1.0 manual.
Scope of delivery (per EFL-D link kit)
| EFL-D Digital fiber link – Input side box | 1 pc |
| EFL-D Digital fiber link – Output side box | 1 pc |
| Foam lined transport box (330 × 272 × 82 mm) | 1 pc |
Recommended accessories
| Power adaptor 100–240 V to 5 V, 3 A, 2.1 mm screw lock, UK/EU/US/AU plug | EFL-A-AD1 (2 pcs are recommended) |
| Fiber patch cable SMA905-SMA905, 10 m Duplex fiber Termination: 2 × SMA905 on both ends Optical mode: OM1 Core / cladding: 62.5/125 µm Length: 10 m |
EFL-A-FPC10 |
| Fiber patch cable SMA905-SMA905, 20 m Duplex fiber Termination: 2 × SMA905 on both ends Optical mode: OM1 Core / cladding: 62.5/125 µm Length: 20 m |
EFL-A-FPC20 |
*) Please mark the required accessories in your request for quotation.














